About the Troubleshooting category
|
|
8
|
617
|
February 20, 2025
|
Filament gets stuck at AMS motor
|
|
7
|
256
|
May 6, 2025
|
Tube is loose on the right side of filament buffer
|
|
13
|
484
|
May 6, 2025
|
"failed to get AMS mapping table"
|
|
15
|
425
|
May 6, 2025
|
Slicer not generating bottom support interfaces
|
|
19
|
2945
|
May 6, 2025
|
Polymaker spool woes
|
|
6
|
1451
|
May 5, 2025
|
AMS not recognising correct colour for Bambu filament
|
|
7
|
299
|
May 3, 2025
|
AMS 2 pro won't unread filament spool
|
|
1
|
34
|
May 2, 2025
|
AMS Slot 4 - Red Solid Light
|
|
11
|
2691
|
April 28, 2025
|
What causes the X1 to always seem to forget about the AMS?
|
|
1
|
32
|
April 28, 2025
|
AMS Screws
|
|
4
|
39
|
April 27, 2025
|
Advice to AMS users printing Abrasives... Check your PTFE tubes ;)
|
|
0
|
37
|
April 26, 2025
|
AMS won't feed past buffer
|
|
2
|
36
|
April 26, 2025
|
AMS Lite Slot 4 Not Detecting Filament When Inserted
|
|
0
|
35
|
April 25, 2025
|
Overture filament doesn't retract in AMS even with insert
|
|
5
|
1110
|
April 25, 2025
|
AMS wrong Auto Refill Grouping
|
|
8
|
323
|
April 23, 2025
|
Questions about swapping AMS units between printers
|
|
13
|
439
|
April 23, 2025
|
Are these AMS and AMS HUB resistance measurement values normal?
|
|
6
|
63
|
April 23, 2025
|
My hotend got stuck in the A1 and I couldn't get it out
|
|
2
|
1298
|
April 22, 2025
|
Filament getting stuck after feeder tube
|
|
2
|
100
|
April 22, 2025
|
Filament ran out error mid print, but there is still filament on spool
|
|
0
|
32
|
April 22, 2025
|
Replacement AMS pneumatic connector
|
|
11
|
69
|
April 18, 2025
|
Feeder detects filament, then says its gone lol
|
|
1
|
40
|
April 17, 2025
|
AMS2 Pro - Filament not detected at extruder
|
|
7
|
231
|
April 15, 2025
|
AMS filament detection not working
|
|
18
|
5074
|
April 8, 2025
|
Downgrade just the AMS firmware
|
|
2
|
117
|
April 7, 2025
|
AMS no longer recognising Wood PLA
|
|
22
|
1073
|
April 3, 2025
|
AMS fail to pullback
|
|
1
|
51
|
March 29, 2025
|
AMS stops feeding just short of extruder
|
|
10
|
2124
|
March 24, 2025
|
NFC / RFID reading not working
|
|
14
|
2409
|
March 22, 2025
|