About the Bambu Lab P1 Series category
|
|
48
|
11090
|
May 29, 2025
|
Not so clean PETG Prints
|
|
11
|
173
|
June 19, 2025
|
P1S quite mode start up
|
|
0
|
14
|
June 19, 2025
|
Nozzle size change from Bambu Studio
|
|
21
|
280
|
June 19, 2025
|
First few layers are good, after that - a disaster
|
|
7
|
849
|
February 16, 2024
|
Hi I’m new here but need a few answers
|
|
5
|
73
|
June 18, 2025
|
Dark Tiles
|
|
2
|
42
|
June 18, 2025
|
New Firmware (1.8.1.0): Can no longer connect to printer
|
|
16
|
650
|
June 18, 2025
|
Is this a bug or something I was unaware of?
|
|
1
|
52
|
June 18, 2025
|
P1S prints what were successfull before, messed up
|
|
2
|
62
|
June 18, 2025
|
AMS feeding issue while manual feeding work
|
|
0
|
26
|
June 18, 2025
|
Purge Tower Hanging Off Plate
|
|
0
|
33
|
June 18, 2025
|
Warping Issues with PA6-GF Filament
|
|
10
|
1196
|
June 18, 2025
|
P1S Stuck in Loop After Purging. Slamming into sides Before Repeating
|
|
8
|
158
|
June 17, 2025
|
Do I need a new filament buffer to hook up the AMS 2 Pro on a P1S?
|
|
7
|
151
|
June 17, 2025
|
Wavy Prime Tower outline for first couple of layers
|
|
0
|
24
|
June 17, 2025
|
P1S belt not centered on idler pulley, making horrible sound
|
|
23
|
9817
|
June 17, 2025
|
P1S All Prints Lifting w/Multiple Beds
|
|
2
|
63
|
June 17, 2025
|
P1S no longer prints properly
|
|
7
|
133
|
June 17, 2025
|
Cost to run the P1S
|
|
11
|
107
|
June 16, 2025
|
P1S layer banding (no successful prints in 3 months of ownership)
|
|
39
|
586
|
June 16, 2025
|
Is this a bed level problem?
|
|
5
|
93
|
June 16, 2025
|
Simplify Model
|
|
15
|
128
|
June 16, 2025
|
2 identical P1S - different results
|
|
9
|
178
|
June 16, 2025
|
Printing recycled PET
|
|
10
|
3847
|
June 16, 2025
|
AMS feed problem?
|
|
0
|
41
|
June 16, 2025
|
0.2mm nozzle calibration inconclusive
|
|
0
|
35
|
June 16, 2025
|
PETG first layer problems
|
|
13
|
5620
|
June 16, 2025
|
SD Card weird behavior
|
|
2
|
47
|
June 16, 2025
|
MQTT with P1S
|
|
11
|
2345
|
June 16, 2025
|