|
TPU Assist module with P2S
|
|
1
|
18
|
July 19, 2026
|
|
Filament won't extrude if AMS involved (spools to extruder, spools back again)
|
|
6
|
179
|
July 19, 2026
|
|
Chamber heater for P2S
|
|
16
|
4758
|
July 19, 2026
|
|
One AMS spool does not cut cleanly but othe 7 okay. Huh?
|
|
2
|
34
|
July 18, 2026
|
|
Hot end mess- how on earth do I deal with this?
|
|
5
|
67
|
July 18, 2026
|
|
My New P2S is otw!
|
|
16
|
455
|
July 18, 2026
|
|
Help with radius surface
|
|
3
|
60
|
July 17, 2026
|
|
Printing ABS-GF when magnetic build-plate came off, du heck
|
|
2
|
81
|
July 16, 2026
|
|
V 2.7.01.57 “please install network plug in before log in
|
|
23
|
2176
|
July 16, 2026
|
|
High flow hotend slower than normal
|
|
3
|
431
|
July 14, 2026
|
|
Sudden severe TPU print quality issues after latest P2S & Bambu Studio updates?
|
|
6
|
394
|
July 13, 2026
|
|
Opposite print angles; how to fix?
|
|
5
|
121
|
July 11, 2026
|
|
Bambu Lab P2S print starts after 1.5 minutes!
|
|
46
|
5324
|
July 11, 2026
|
|
Bad top layer on large surfaces
|
|
8
|
138
|
July 10, 2026
|
|
P2S VFA is simply terrible
|
|
183
|
14732
|
July 9, 2026
|
|
P2S: Extruder Overload
|
|
257
|
23187
|
July 8, 2026
|
|
Disabling P2S Aux Fan
|
|
38
|
9142
|
July 7, 2026
|
|
Z-axis motor noise reduction
|
|
2
|
96
|
July 7, 2026
|
|
Problems with replacement printer
|
|
3
|
102
|
July 5, 2026
|
|
Bad print on parts with support
|
|
3
|
118
|
July 5, 2026
|
|
P2S + VentoBox, someone has any "scientific" VOC measurments?
|
|
36
|
6231
|
July 5, 2026
|
|
P2S High Flow .6 quality issues
|
|
1
|
282
|
July 5, 2026
|
|
P2S filament runout while Direct Drive top mount
|
|
1
|
94
|
July 5, 2026
|
|
Is the FNATR filter system good?
|
|
9
|
159
|
July 2, 2026
|
|
P2S Optimized Start/End G-code
|
|
0
|
169
|
July 2, 2026
|
|
P1S printing TPU with a PLA interface layer?
|
|
3
|
70
|
July 2, 2026
|
|
Where does this pin belong?
|
|
10
|
372
|
July 1, 2026
|
|
TPU feed assist module - where to connect on a P2S?
|
|
18
|
264
|
June 30, 2026
|
|
Loading filament
|
|
7
|
167
|
June 30, 2026
|
|
My P2S started printing before reachin the right chamber temperature
|
|
2
|
123
|
June 27, 2026
|